> >>JetCat P220-PRO-S2-R1
JetCat P220-PRO-S2-R1 Bekijk groter

JetCat P220-PRO-S2-R1

JC22R1

Nieuw product

JetCat P220-PRO-S2-R1

Meer details

1 Item

4 297,52 €

Meer informatie

JetCat P220-PRO-S2-R1 Engine:

Introduction

The P220-PRO-S2-R1 turbo-jet engine is designed as a propulsion unit for RC-aircraft and/or drones.
The engine is lubricated by fuel with oil admixture.

Versus other P220-PRO derivates  this engine is tuned/setup for quickest possible startup time.Under normal conditions the engine will startup within 6-8sec to idle! Max rpm can be reached within 10-12sec after startup command.


The engine is equipped with a BLDC starter), 1x BLDC fuel pump, 1x Startup pumpm2x fuel solenoids and electronic control system
(FADEC type).
The engine may be modified based on customer specific requirements and to meet different operating / installation
conditions. The engine is available with two different nozzles (long/short).


Functional description
The P220-PRO-S2-R1  is a single-shaft engine comprising a single-stage radial compressor, annular combustion
chamber, single stage axial turbine and fixed exhaust nozzle. At the compressor intake, there is a brushless starter
system mounted. Intake air is compressed in the radial compressor stage, proceeds through the radial and axial
diffuser into the combustion chamber where it is mixed with vaporized fuel. Combustion gases generated by fuel
burning in the combustion chamber expand through the single state axial turbine and the exhaust nozzle to the
atmosphere. The gas exiting the exhaust cone produces the required thrust. The rotor of the engine is mounted on 2
ball bearings lubricated by a fuel/oil mix.


Control options / electrical interface
The JetCat-PRO engine series provides the highest level of integration and maximum ease of installation.
All peripheral systems necessary for the engines operation are fully integrated below the engines front cowling.

JetCat P220-PRO engine features/functions
Integrated Engine sided Components:

  • ECU (electronic control unit), fully programmable via detachable Ground Support Unit (GSU)
  • Brushless starter and seal free brushless fuel pump
  • Fuel & Kerosene-start solenoids
  • Post Fuel filter downstream of the pump (last barrier filter)
  • Barometric altitude / pressure sensor allowing for automatic engine tuning upon operation altitude.
  • 4-pin Molex expansion connector (e.g. for smoke pumps/ fuel transfer pumps/GSU)
  • Optional bleed-air port (e.g. for pressurization of fuel system)
  • Direct quick start on kerosene via integrated high speed / low current ignition system
  • High altitude, high flight speed in-air restart capability
  • Automatic engine cool down cycle after shutting down.
  • Reporting of fuel consumed / fuel flow rate / fuel burned / remaining fuel in tank.
  • Engine/ECU power On/Off via voltage control signal
  •  No external power switches required.
  • Engine safety shut down input, for instant engine shut down via (flight) termination system. This will kill.

power to fuel pump and shut off safety solenoid valves and stop engine in any case on a multiple redundant.

way, whilst ECU can stay powered on (for continued data reporting and or engine cool down).

  • Monitoring and reporting of all currents / voltages (e.g. supply voltage / current, pump driving voltage) as

well as all engine life parameters / setpoints.

  • Automatic fuel purge feature for automatic filling/purge of fuel feed lines. As soon as fuel arrives at the

engine, purging will automatically terminate.

  • High performance ceramic bearings

 

Applications:

  • Propulsion of small radio-controlled model aircraft (ideally suited for models up to 25kg takeoff mass)
  • UAV’s

 

Notes:

Engine is available in different setups:

Engine is available in different setups:

 

  • Different nozzle length available to support easier integration depending on installation situation, currently 3x different nozzle lengths are available. This allows to remove or shorten tail pipes in many cases. Latest types also have 4x90° “radial type” mounting features added.
  • Different styles of fuel inlet ports (Festo fuel fittings or “Swagelock” fittings)

If you like to order this turbine call or mail for the Delivery time and latest prices to

info@modelaircraftcompany.com or +31638513063

  •